Error code E3

If your Gorenje washing machine has error code E3, there is an error with the water level

If your washing machine takes in enough or too much water so that it comes out of the door, the level control is probably faulty.

Error code E4

If your Gorenje washing machine has the error code E4, there is a fault with the tachogenerator.

If your washing machine uses motor carbon, error code E4 may be due to the motor carbon being worn out. You can find motor coal below.

If your washing machine does not support motor coal, but in places has a three-phase motor, error code F5 is typically due to the tachogenerator or the motor itself being faulty. However, in most cases it is the tachogenerator that is faulty.

Error code E6

If your Gorenje washing machine has error code E6, there is a temperature error.

With error code E6, your washing machine indicates that the temperature of the water is too low. First turn off the machine for 10 seconds and then turn on the machine again and set the program to run. If the error is still displayed, the heater is defective.

Find heater here

Error code F1

If your Gorenje washing machine has error code E11, it is due to a fault in the water supply

• Error code E11 typically occurs when the supply hose with aquastop or the solenoid valve is defective.

Error code F2

If your Gorenje washing machine has error code F2, it is because the door is open.

Check whether you have closed the door correctly. If the door won't close at all, there are problems with the door lock. You will find a new door lock below.

Find door lock here

Error code F3

If your Gorenje washing machine has error code F3, there is a water level error.

If you experience the error code F3, the level control has registered that not enough water could enter the washing machine.

• Check the water supply and whether there is enough pressure from the connection point. You can do this by disconnecting the supply hose, putting a bucket under it and turning on the tap.
• Check if the pressure switch hose is blocked. By blowing into the hose, you can blow into the hose to check for resistance. If you don't feel resistance, you can soak the hose in lukewarm water, hoping that will remove any foreign matter from the hose.
• It may also be because the level control is faulty.
• Error code E13 usually occurs when the level control has failed.
• If none of the above removed the error code, it is possible that the cause is a faulty control.

Find level control here Find pressure switch here Find control here

Error code F4

If your Gorenje washing machine has the error code F4, there is a fault with the tachogenerator.

When the error code F4 appears on your Goronje washing machine, it typically means that the connection to the tachogenerator is disconnected or loose.

If your washing machine uses motor carbon, error code E4 may be due to the motor carbon being worn out. You can find motor coal below.

If your washing machine does not use motor coal, it may be the three-phase motor or the tachogenerator that is to blame for the error code F4. Typically, it is the tachogenerator that is defective.

Error code F5

If your Gorenje washing machine has error code E21, it is due to a communication error.

Error code F5 occurs when there is no connection between the main control module and other control modules. You can fix the problem by checking for loose connections.

Error code F6

If your Gorenje washing machine has error code F6, there is a fault with the heating element.

The error code F6 is typically due to a faulty heater due to a lack of descaling.

Error code F7

If your Gorenje washing machine has error code F7, there is an error with emptying the water.

1. Disassemble the wire strainer and let the water run out. If no water comes out, the bottom hose is blocked. Clean the bottom hose with a curtain spiral or similar.
2. Remove the drain hose and blow into it. If you encounter resistance, clean the drain hose with a curtain spiral or similar.

Error code F8

If your Gorenje washing machine has error code F8, there is a motor fault.

Error code F8 can be caused by many different errors. It would be best if you call us on: 98 18 21 00

Error code F9

If your Gorenje washing machine has error code F9, there is an error in the water supply.

• The error code F9 occurs when either the inlet hose with aquastop or the solenoid valve is defective.